Showing 17–32 of 834 results
LED Strobe Light Version, High performance MCU, 16pcs high power IR LED, Environmental brightness detection, switch on under low illumination
IT-3103SZN-WLSL is a high power and smart performance digital pulse strobe lamp applying for Intelligent Traffic System applications. It’s suitable for traffic crossing; urban road and high way for number plate recognition and speed measurement. Complied with latest professional strobe control circuit, it can accurately control strobe flash time, brightness and output of high instantaneous power. It has rapid recycling time and long lifespan, through synchronization with the strobe lamp, ITS cameras can obtain clear pictures of number plate, vehicle body and cab under any kind of environment with less influence of human eye.
LED Strobe Light Version, High performance MCU, 14pcs high power IR LED, Environmental brightness detection, switch on under low illumination
IT-3104SZN-WLSL is a high power and smart performance digital pulse strobe lamp applying for Intelligent Traffic System applications. It’s suitable for traffic crossing; urban road and high way for number plate recognition and speed measurement. Complied with latest professional strobe control circuit, it can accurately control strobe flash time, brightness and output of high instantaneous power. It has rapid recycling time and long lifespan, through synchronization with the strobe lamp, ITS cameras can obtain clear pictures of number plate, vehicle body and cab under any kind of environment with less influence of human eye.
IT-3105SZN-IRSL is designed as the high efficacy strobe light for highway intelligent monitoring recording system and red light auto recording system.
IT-3105SZN-WLSL is designed as the high efficacy strobe light for highway intelligent monitoring recording system and red light auto recording system.
IT-3128SZN-WLSL Digital LED Strobe Light is a high power and smart performance digital pulse strobe lamp applying for Intelligent Traffic System applications. It’s suitable for traffic crossing; urban road and high way for number plate recognition and speed measurement. Complied with latest professional strobe control circuit, it can accurately control strobe flash time, brightness and output of high instantaneous power. It has rapid recycling time and long lifespan, through synchronization with the strobe lamp, ITS cameras can obtain clear pictures of number plate, vehicle body and cab under any kind of environment with less influence of human eye.
IT-485-CAN is suitable for data exchange between CAN-Bus field bus and RS-485 bus interface converter, and supports Modbus RTU protocol. IT-485-CAN interface converter integrated a RS-485 channel and a CAN-Bus channel can be easily embedded using RS-485 interface for communication nodes, do not need to change the original hardware architecture enables the device to obtain the CAN-Bus communication interface, to achieve between the equipments of RS-485 and CAN-Bus network connection and data communication. RS-485 channel IT-485-CAN devices to support a variety of baud rate, the range is 300bps~115200bps. CAN-Bus channel support CiA recommended a variety of standard baud rate and user-defined baud rate, the range of 2.5Kbps~1Mbps. IT-485-CAN interface converter provides three types of data conversion: transparent conversion, encryption conversion and Modbus protocol conversion. Its exterior design supports DIN-Rail mounting and Wall mounting, which is convenient for engineering application. The board comes with a photoelectric isolation module, complete electrical isolation control circuit and CAN-Bus communication circuit, so that the IT-485-CAN converter has a strong anti-interference ability, greatly improving the system in the harsh environment of the use of reliability.
IT-485I-USB is kind of industrial USB to RS-232/485/422 converter, plug and play, 9-48VDC external power supply or USB power supply or both of them, it support DIN-Rail and wall mounting installation, can support latest operation system, wide working temperature, 2KVAC isolation protect, easy using for your projects.
The Intellisystem IT-485P5-TTL is a bi-directional port powered RS-485 to 5V TTL converter in a 9 pin format. It can convert any standard full duplex RS-485 port to a 5V TTL signal and vice versa. The unit is powered from the RS-485 data lines. It also supports data direction auto-turnaround. Therefore, no external power or flow control is required. The data direction auto-turnaround automatically enables the TTL driver when data is present on the RS-485 side making the device plug-and-play, requiring no software drivers. The IT-485P5-TTL has a DB9 male connector on the RS485 side or 5-way terminal block and either a DB9 male connector or 5-way terminal block on the TTL side. Separate terminal block is included in package.
10/100M Ethernet to 4xE1 Bridge
The IT-7210-PC inverse multiplexers transmit up 8 Mbps channel over multiple E1 links. They bridge the gap between E1 and E3, allowing bridges and routers to operate at their fastest rates. The IT-7210-PC have a built-in 10/100 Ethernet bridge with VLAN support for LAN-to-LAN applications over 4 E1 links. The IT-7210-PC fully meets all of the E1 specifications including G.703, G.704. The unit features diagnostic capabilities for performing remote loopback tests.
10/100M Ethernet to E1 Bridge
IT-7211-PC bridge provides easy conversion from ITU-T G.703 E1 channel to Ethernet interface. Can used widely in connecting between WAN and LAN, monitoring, etc. The Ethernet interface is 10/100Mbps auto negotiation and can be full/half duplex. The E1 is transparent and in full rate, which can support the E1 unframed mode, including fractional E1 per request. A pair of IT-7211-PC offer a cost effective solution for using existing E1 leased lines for transparent Ethernet service. Local management of the IT-7211-PC Converter is provided via DIPswitches. Front panel LEDs monitor the G.703 link, Ethernet LAN and serial ports for status and Loss of Sync.
IT-7211-PC compact G.703 Access Converter provides E1/2.048 Mbps Network Termination as well as serial or Ethernet LAN interface conversion in a standalone or rack mount package.
IT-7211-PC terminates the G.703 Telco interface and converts the data for transmission to a user-oriented 10/100BaseT(x) interface.
10/100M Ethernet to E1 Bridge
IT-7212-PC bridge provides easy conversion from ITU-T G.703 E1 channel to Ethernet interface. Can used widely in connecting between WAN and LAN, monitoring, etc. The Ethernet interface is 10/100Mbps auto negotiation and can be full/half duplex. The E1 is transparent and in full rate, which can support the E1 unframed mode, including fractional E1 per request. A pair of IT-7212-PC offers a cost effective solution for using existing E1 leased lines for transparent Ethernet service. Local management of the IT-7212-PC Converter is provided via DIPswitches. Front panel LEDs monitor the G.703 link, Ethernet LAN and serial ports for status and Loss of Sync.
IT-7212-PC compact G.703 Access Converter provides E1/2.048 Mbps Network Termination as well as serial or Ethernet LAN interface conversion in a standalone or rack mount package.
IT-7212-PC terminates the G.703 Telco interface and converts the data for transmission to a user-oriented 10/100BaseT(X) interface.
V.35 to E1 (Framed E1) Converter
IT-7221-PC converter provides conversion between ITU-T G.703 standard E1 interface and standard V.35 interface, can convert E1 channel of SDH, PDH, and other Optical Transmission Equipment or microwave, satellite Equipment to V.35 channel, Extend V.35 channel of DDN. Used widely in data communication networks, Connecting with V.35 interface of Routers and Optical Transmission Equipments without G.703 interface, realize match between different network equipments, and transparent to upper protocol layer.
E1 Optic Fiber Modem
IT-7301-PC E1 Fiber Modem is a high-performance E1 fiber optic modem developed by using a dedicated integrated circuit. It is to modulate a framing or non-framing E1 data signal directly into single- or multi-mode optic fiber for a transmission via optic cable line. At another end of the optic cable, optical signal is demodulated into a framing or non-framing E1 data signal. E1 interface may be directly connected with the E1 interfaces of image and data terminals or the WAN ports of MUX, exchanger and router for a dedicated network setup or a LAN connection.
E1 Optic Fiber Modem
IT-7302-PC E1 Fiber Modem is a high-performance E1 fiber optic modem developed by using a dedicated integrated circuit. It is to modulate a framing or non-framing E1 data signal directly into single- or multi-mode optic fiber for a transmission via optic cable line. At another end of the optic cable, optical signal is demodulated into a framing or non-framing E1 data signal. E1 interface may be directly connected with the E1 interfaces of image and data terminals or the WAN ports of MUX, exchanger and router for a dedicated network setup or a LAN connection.