Italiano
IT-DIN-15S Series
15 Watts Single Output Industrial DIN Rail Power Supply Series
- Two stages of constant current circuit avoid LED away from instantly impulse impact when started.
- Low failure rate of products is guaranteed by the professional in-house optimized independent circuit technology, which has been widely used in our LED illuminators for more than 5 years.
- Wide edge of silica gel circle and water stop line ensure IP66 waterproof and dustproof level.
- Twice direct cooling heat sink processing enable to increase the cooling coefficient and prolong the service life of the product.
- Patent design hexagonal spherical light sensor more accurately responses ambient brightness and improves accuracy of automatic light control.
- Flexible angle adjustable bracket can extend the illuminance range widely.
- IP66 waterproof and dustproof housing available work at ambient temperature -40°C to 50°C.
- Professional Design
- Description
- Technical Specifications
- Block Diagrams
- Mounting Methods
- Graphs & Curves
- Mechanical Drawings
- Download / Documentation
- Contact US / Requests
Description
15 Watts Single Output Industrial DIN Rail Power Supply Series
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
TECHNICAL SPECIFICATIONS
| MODEL | IT-DIN-15S-12 | IT-DIN-15S-24 | ||
|---|---|---|---|---|
| OUTPUT | DC Output | 12V | 24V | |
| Rated Current | 1.25A | 0.65A | ||
| Current Range Note 1 | 0~1.25A | 0~0.65A | ||
| Ripple and Noise | 10~70℃ | ≤120mV | ≤120mV | |
| Note 2 | .-25~10℃ | ≤240mV | ≤240mV | |
| Voltage ADJ. Range | 12~14V | 24~28V | ||
| Voltage Accuracy | ±1.0% | |||
| Line Regulation | ±0.5% | |||
| Load Regulation | ±1% | |||
| Set-up Time | <1.5S @230Vac Full load | |||
| Hold up Time | ≥20mS @230Vac Full load | |||
| Temperature Coefficient | ±0.03%/℃ | |||
| Overshoot and Undershoot | <5.0% | |||
| INPUT | Voltage Range | 90Vac~264Vac, 127VDC-370VDC | ||
| Frequency Range | 47Hz~63Hz | |||
| Efficiency ( Typical) | 83% @230Vac input, full load | 84.5% @230Vac input, full load | ||
| AC Current (max.) | <0.5A | |||
| Inrush Current (Typical) | 50A/230Vac Cold start | |||
| Leakage Current | Input—output: ≤0.25mA Input—PE: ≤3.5mA (264Vac input, 63Hz) | |||
| PROTECTION | Over Load | 1.5~2.0A, hiccup mode, auto recovery | 0.7~1.0A, hiccup mode, auto recovery | |
| Over voltage | 15.0~16.8V, Constant voltage, auto recovery | 28.8~31.2V, Constant voltage, auto recovery | ||
| Short Circuit | Long-term mode, auto recovery | |||
| ENVIRONMENT | Operating amb. Temp. & Hum. | .-25℃~70℃; 20%~90%RH No condensing | ||
| Storage Temp. & Hum. | .-40℃~85℃; 5%~95%RH No condensing | |||
| SAFETY &EMC | Safety Standards | UL60950, EN60950 | ||
| Note 3 | Withstand Voltage | Primary-Secondary: 3KVac/10mA; Primary-PE: 1.5KVac/10mA; Secondary-PE: 0.5KVac/10mA | ||
| Isolation Resistance | >10M ohms | |||
| EMC Emission | Compliance to EN55022, EN55024 Class B | |||
| Harmonic Current | Compliance to EN61000-3-2 ， CLASS A | |||
| EMC Immunity | Compliance to EN61000-4-2,3,4,5,6,11; heavy industry level | |||
| OTHERS | MTBF (MIL-HDBK-217F) | 590,000Hrs (25℃, Full load) | ||
| Dimension (L*W*H) | 103.7*32*97.5mm | |||
| Packing | 36pcs/CTN | |||
| Cooling method | Cooling by free air convection | |||
| NOTE | 1. All parameters NOT specially mentioned are measured at rated input, rated load and 25℃ of ambient temperature. | |||
| 2. Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor. |
RSS - Posts
You must belogged in to post a comment.