IT-DIN-120 Series

120 Watts Single Output Industrial DIN Rail Power Supply Series

Universal AC input range(85~264Vac)
Support 1+1 or N+1 redundant system（suggest to use redundancy modules.）
Built-in active PFC,PF>0.95
High efficiency up to 91%
Built-in current sharing function
Built-in current limiting circuit
Output protections: OVP/OLP/SCP/OTP
Wide operating ambient temp (-25℃~70℃)
150% peak load capacity
Easy Fuse Tripping due to High Overload Current
Excellent Partial Load Efficiency
Built-in DC OK relay contact
Can be installed on TS-35/7.5 or TS-35/15
100% full load burn-in test
Suitable for critical applications
Ultra-slim,32mm width
3 years warranty

Categories: Industrial Power Supply, DIN Rails, Products Tags: 10~70℃, 10A, 12~14V, 120 W, 124*119*32mm, 12V, 2.5A, 24~28V, 24V, 47Hz~63Hz, 48~56V, 48V, 5A, DIN Rail, Single Output

Description

120 Watts Single Output Industrial DIN Rail Power Supply Series

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

TECHNICAL SPECIFICATIONS

MODEL			IT-DIN-120-12	IT-DIN-120-24	IT-DIN-120-48
OUTPUT	DC Output		12V	24V	48V
	Rated Current		10A （ pls refer to derating curve ）	5A	2.5A
	Current Range Note 1		0~10A	0~5A	0~2.5
	Ripple and Noise	0~70℃	≤100mV	≤120mV	≤240mV
	Note 2	.-25℃	≤200mV	≤240mV	≤240mV
	Voltage ADJ. Range		12~14V	24~28V	48~56V
	Voltage Accuracy		±1.0%
	Line Regulation		±0.5%
	Load Regulation		±1.0%
	Set-up Time		<250mS@230Vac ; <500mS@100Vac
	Hold up Time		≥20mS(230Vac input, Full load)
	Temperature Coefficient		±0.03%/℃
	Overshoot and Undershoot		<5.0%
INPUT	Voltage Range		85Vac~264Vac, 127Vdc-360Vdc
	Frequency Range		47Hz~63Hz
	Power Factor (typical)		0.99/100Vac 0.95/230Vac
	Efficiency ( Typical)		89.5%	0.91	0.92

	AC Current (max.)		<1.5 A/100Vac <0.65A/230Vac
	Inrush Current (Typical)		＜ 30A/100Vac ＜ 60A/230Vac Cold start
	Leakage Current		Input—output:<0.25mA Input—PG:<3.5mA
PROTECTION	Over Load		110%~150% of rated current, Constant current limiting for some time(150% of rated current, last 3S) then PS stop working for 7S,after 7S,if the load <=rated current, PS will work normally, auto recovery
	Over voltage		15~18V	29~33V	58~65V
			Protection type: Hiccup mode, Auto recovery
	Over temperature		100±5℃, detect on heat sink of power transistor; shut down O/P, auto recovery after temperature goes down.
	Short Circuit		Long-term mode, auto recovery
ENVIRONMENT	Operating amb. Temp. & Hum.		.-25℃~70℃; 20%~90%RH No condensing
	Storage Temp. & Hum.		.-40℃~85℃; 5%~95%RH No condensing
SAFETY &EMC	Safety Standards		meet UL508, UL60950, EN60950
Note 3	Withstand Voltage		Primary-Secondary: 3.0KVac; ≤10mA .Primary-PG: 2.5KVac; ≤10mA. Secondary-PG: 0.5KVac≤10mA.
	Isolation Resistance		≥100M ohms
	EMC Emission		Compliance to EN55022, EN55024, FCC PART 15 Class B
	Harmonic Current		Compliance to EN61000-3-2, CLASS A
	EMC Immunity		Compliance to EN61000-4-2,3,4,5,6,8,11; heavy industry level
OTHERS	MTBF (MIL-HDBK-217F)		More than 300,000Hrs (25℃, Full load)
	Dimension (LWH)		12411932mm
	Packing		28pcs/CTN,18.02Kgs, 0.04cbm
	Cooling method		Cooling by free air convection

Additional function	Power boost		150% of rated current
	DC OK		V On: when output voltage is up to 90% of rated output voltage
			V Off: when output voltage is down to 80% of rated output voltage
	DC OK relay contact rating		Max 30V/1A or 60V/0.3A or 30Vac/0.3A Resistive load
	Parallel function		support
NOTE	1. All parameters NOT specially mentioned are measured at rated input, rated load and 25℃ of ambient temperature.
	2. Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor.