Once installation is complete, the
Administrator should proceed to the next section "Initial access to the
Network Camera" for necessary checks and configurations.
The IT3G50-IT3G50W IT3G50/IT3G50W Network
Camera can be connected either before or immediately after software installation
onto the Local Area Network. The Administrator should complete the network
settings on the configuration page, including the correct subnet mask and IP
address of gateway and DNS. Ask your network administrator or Internet service
provider for the detail information. By default the IT3G50-IT3G50W
IT3G50/IT3G50W Network Camera requires the Administrator to run installation
every time it reboots. If the network settings are to remain unchanged, disable
the Install option. Refer to “Network settings” on the System Configuration
page for details. If any setting is entered incorrectly and cannot proceed to
setting up the IT3G50-IT3G50W Network Camera, restore the factory settings
following the steps in the “Troubleshooting” chapter of the Appendix.
The default Administrator’s password is
blank and the IT3G50-IT3G50W IT3G50/IT3G50W Network Camera initially will not
ask for any password. The Administrator should immediately implement a new
password as a matter of prudent security practice. Once the Administrator’s
password is saved, the IT3G50-IT3G50W IT3G50/IT3G50W Network Camera will ask
for the user’s name and password before each access. The Administrator can set
up a maximum of twenty (20) user accounts. Each user can access the
IT3G50-IT3G50W IT3G50/IT3G50W Network Camera except to perform system
configuration. Some critical functions are exclusive for the Administrator,
such as system configuration, user administration, and software upgrades. The
user name for the Administrator is permanently assigned as “root”. Once the
password is changed, the browser will display an authentication window to ask
for the new password. Once the
password is set, there is no provision to recover the Administrator’s password. The only option is to restore to the original
factory default settings.
After opening the Web browser and typing in
the URL of the IT3G50-IT3G50W Network
Camera, a dialogue window pops up to request a username and password. Upon
successful authentication, the following figure is displayed.
The foreground is the login window and the
background shows the message if authentication fails. The user may check the
option box to save the password for future convenience. This option is not available to the
Administrator for obvious reason.
For the initial access to the
IT3G50/IT3G50W Network Camera in Windows, the web browser may prompt for
permission to install a new plug-in for the Network Camera. Permission request
depends on the Internet security settings of the user’s PC or notebook. If the
highest security level is set, the computer may prohibit any installation and
execution attempt. This plug-in has been registered for certificate and is used
to display the video in the browser. Users may click on 
to proceed. If the web browser does not allow
the user to continue to install, check the Internet security option and lower
the security levels or contact your IT or networking supervisor for help.
The main page layout has two parts:
Configuration functions: The camera can be configured using these user interfaces.
Camera View:
What the IT3G50-IT3G50W camera sees.
Click on
the configuration link to the left of the image window to enter the
configuration page.
Click
on the magnifier icon under the camera view then the digital zoom control panel
will be shown. Uncheck “Disable digital zoom” and use the slider control to
change the zoom factors.
Click
on “Snapshot”, web browser will pop up a new window to show the
snapshot. Users can pint at the snapshot and click the right button of mouse to
save it.
At
the initial access to the “Connection type” page in Windows, the web browser
will ask for a new plug-in installation, the plug-in being the IT3G50-IT3G50W
Network Camera. This plug-in has been registered for certification and can be
used to change the parameters at the client’s site. The user may click on 
to install the plug-in. If the web browser
does not allow the user to complete the installation, check the Internet
security to lower the security level or contact your IT or networking
supervisor.
There
are two settings for the client side. One is “Media Options” for users
to determine the type of media to be streaming. The other is “Protocol
Options” which allows choices on connection protocol between client and
server. There are two protocols choices to optimize your usage – UDP and TCP.
The
UDP protocol allows for more real-time audio and video streams. However,
some packets may be lost due to network burst traffic and images may be
obscured.
The
TCP protocol allows for less packet loss and produces a more accurate
video display. The downside with this protocol is that the real-time effect is
worse than that with the UDP protocol.
If
no special need is required, UDP protocol is recommended. Generally speaking,
the client’s choice will be in the order of UDP → TCP. After the IT3G50-IT3G50W IT3G50/IT3G50W Network Camera is connected
successfully, “Protocol Option” will
indicate the selected protocol. The selected protocol will be recorded in the
user's PC and will be used for the next connection. If the network environment
is changed, or the user wants to let the web browser to detect again, manually
select the UDP protocol, save, and return HOME to re-connect.
<url> http://<IT3G50/IT3G50W
Network Camera>/client.html
<IT3G50/IT3G50W
Network Camera> is the domain name or the original IP address of the
IT3G50-IT3G50W Network Camera.
Best
performance generally equates to the fastest image refresh rate with the best
video quality, and at the lowest network bandwidth as possible. The three
factors, “Maximum frame rate”, “Constant bit rate”, and “Fix quality” on the
Audio and Video Configuration page, are correlative to allow for achieving the
best performance possible.
For Best
Real-Time Video Images
To
achieve good real-time visual effect, the network bandwidth should be large
enough to allow a transmission rate of greater than 20 image frames per second.
If the broadband network is over 1 Mbps, set the “Fix bit rate” to 1000Kbps or
1200Kbps, and set “Fix quality” at the highest quality. The maximum frame rate
is 30. If your network bandwidth is more than 512Kbps, you can fix the bit rate
according to your bandwidth and set the maximum frame rate to 30 fps. If the
images vary dramatically in your environment, you may want to slow the maximum
frame rate down to 20 fps in order to lower the rate of data transmission. This
allows for better video quality and the human eyes cannot readily detect the
differences between those of 20, 25, or 30 frames per second. If your network
bandwidth is below 512 Kbps, set the “Fix bit rate” according to your bandwidth
and try to get the best performance by fine-tuning with the “Maximum frame
rate”. In a slow network, greater frame rate results in blur images. Another
work-around is to choose “160x120” in the “Size” option for better images.
Video quality performance will vary somewhat due to the number of users viewing
on the network; even when the parameters have initially been finely tuned. Performance will also suffer due to poor
connectivity because of the network’s burst constraint.
Only Quality
Images Will Do
To
have the best video quality, you should set “Fix quality” at “Detailed” or
“Excellent” and adjust the “Maximum frame rate” to match your network’s
bandwidth. If your network is slow and you receive “broken” pictures, go to the
TCP protocol in “Connection type” and choose a more appropriate mode of
transmission. The images may suffer a time delay due to a slower connection. The delay will also increase with added
number of users.
Somewhere Between
Real-Time and Clear Images
If
you have a broadband network, set “Fix quality” at ”Normal” or better, rather
than setting “Fix bit rate”. You can also fix the bandwidth according to your
actual network speed and adjust the frame rate.
Start from 30 fps down for best results but not below 15 fps. If the image qualities are not improved,
select a lower bandwidth setting.
Protect
IT3G50/IT3G50W Network Camera by passwords
The
IT3G50-IT3G50W IT3G50/IT3G50W Network Camera is shipped without any password by
default. That means everyone can access the IT3G50/IT3G50W Network Camera
including the configuration as long as the IP address is known. It is necessary
to assign a password if the IT3G50/IT3G50W Network Camera is intended to be
accessed by others. Type a new word twice in ➀ to enable protection. This password is used to identify the
administrator. Then add an account with user name and password for your friends
in ➁. IT3G50-IT3G50W IT3G50/IT3G50W Network Camera can provide twenty
accounts for your valuable customers or friends. You may delete some users from
➂.
The
Administrator can use the built-in motion detection to monitor any movement to
perform many useful security applications. To upload the snapshots, users can
choose either email or FTP according to user’s needs. Both e-mail and FTP use
the network settings on the Email and FTP page. Refer to the definition section
for detail configuration.
1.
Click on “Configuration”
on homepage;
2.
Click on “Motion detection” at the left column;
3.
Check “Enable motion
detection”;
4.
Click on new to have a new
window to monitor video;
5.
Type in a name to identify the
new window;
6.
Use the mouse to click, hold,
and drag the window corner to resize or the title bar to move;
7.
Fine-tune using the
“Sensitivity” and “Percentage” fields to best suit the camera’s environment.
Higher ”Sensitivity” detects the slighter motion. Higher “Percentage” discriminates
smaller objects;
8.
Clicking on “Save” enables the
activity display. Green means the motion in the window is under the watermark
set by Administrator and red means it is over the watermark;
9.
Click on “Application”
at the left column;
10.
Check the weekdays as you need
and give the time interval to monitor the motion detection every day;
11.
Select the Trigger on Motion
detection.;
12.
Set the delay before detecting next motion to avoid continuous false alarms
following the original event;
13.
Set the number of pre-event and
post-event images to be uploaded;
14.
Check the window name set in
step 5;
15.
Check the way to upload
snapshot;
16.
Click on save to validate.
An
easy-to-use Upgrade Wizard is provided to upgrade the IT3G50-IT3G50W IT3G50/IT3G50W Network Camera with just a few
clicks. The upgrade function is opened to the Administrator only. To upgrade
the system, follow the procedures below.
1.
Download the firmware file named “xxx.pkg” from the appropriate product folder.
2.
Run the Upgrade Wizard and proceed following the prompts. Refer to the
instructions of the Upgrade Wizard for details.
3.
Or upgrade firmware from HTTP web page directly
3.
The whole process will finish in a few minutes and it will automatically
restart the system.
|
|
 Please use wired
connection to upgrade the firmware. Do not remove the power during the
upgrade process, if power fails during the writing process of Flash memory,
the program in the memory of the Network Camera may be destroyed
permanently. If the Network Camera cannot restart properly, ask your dealer
for technical service.
|
|
Only the Administrator can access system
configuration. Each category in the left column will be explained in the
following pages. The bold texts are the specific phrases on the Option pages.
The Administrator may type the URL below the figure to directly enter the frame
page of configuration. If the Administrator also wants to set certain options
through the URL, read the reference appendix for details.
<url>
http://<IT3G50/IT3G50W Network Camera>/setup/config.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the IT3G50-IT3G50W Network Camera.
<url> http://<IT3G50/IT3G50W
Network Camera>/setup/system.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the IT3G50-IT3G50W Network Camera.
"Host name" The text displays the title at the top of the main page.
“Turn off the LED indicator” Check this option to shut off the LED on the rear. It can prevent
the camera’s operation being noticed.
"Keep current date and time" Click on this to reserve the current date and time of the
IT3G50-IT3G50W Network Camera. An internal real-time clock maintains the date
and time even when the power of the system is turned off.
"Sync with computer time" Synchronizes the date and time of the IT3G50-IT3G50W IT3G50/IT3G50W
Network Camera with the local computer. The read-only date and time of the PC
is displayed as updated.
“Manual”
Adjust the date and time according to what is entered by the Administrator.
Notice the format in the related fields while doing the entry.
“Automatic”
Synchronize with the NTP server over the Internet whenever the IT3G50-IT3G50W
IT3G50/IT3G50W Network Camera starts up. It will fail if the assigned
time-server cannot be reached.
“NTP server”
Assign the IP address or domain name of the time-server. Leaving the text box blank
connects the IT3G50-IT3G50W IT3G50/IT3G50W Network Camera to the default
time-servers.
"Time zone" Adjust the time with that of the time-servers for local settings.
“Update interval” Select hourly,
daily, weekly, or monthly update with the time on the NTP server.
Remember to click on 
to immediately validate the changes.
Otherwise, the correct time will not be synchronized.
“Root password” Change the Administrator’s password by typing in the new password
identically in both text boxes. The typed entries will be displayed as
asterisks for security purposes. After pressing , the
web browser will ask the Administrator for the new password for access.
“Add user”
Type the new user's name and password and press 
to insert the new entry. The new user will be
displayed in the user name list. There is a maximum of twenty user accounts.
“Manager user” Pull down the user list to find the user’s name and press 
to complete.
<url> http://<IT3G50/IT3G50W
Network Camera>/setup/security.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the IT3G50-IT3G50W Network Camera.
Any changes made on this page will restart
the system in order to validate the changes. Make sure every field is entered
correctly before clicking on .
“LAN” & “PPPoE”
The default type is LAN. Select PPPoE if
using ADSL
"Get
IP address automatically" & “Use fixed IP address”
The default status is “Get IP address
automatically”. This can be tedious having to perform software installation
whenever the IT3G50/IT3G50W Network Camera starts. Therefore, once the network
settings, especially the IP address, have been entered correctly, select “Use
fixed IP address” then the IT3G50/IT3G50W Network Camera will skip
installation at the next boot. The IT3G50-IT3G50W IT3G50/IT3G50W Network Camera
can automatically restart and operate normally after a power outage. Users
can run IP installer to check the IP address assigned to the IT3G50/IT3G50W
Network Camera if the IP address is forgotten or using the UPnP function
provided by the IT3G50/IT3G50W Network Camera (MS Windows XP provides UPnP
function at My Network Place). “IP address” This is necessary for
network identification.
“Subnet mask” This is used to determine if the destination is in the same subnet.
The default value is “255.255.255.0”.
“Default router” This is
the gateway used to forward frames to destinations in a different subnet.
Invalid router setting will fail the transmission to destinations in different
subnet.
“Primary DNS” The primary domain name server that translates hostnames into IP
addresses.
“Secondary DNS” Secondary domain name server that backups the Primary DNS.
“Enable
UPnP presentation” Enable the UPnP camera short
cut.
“Enable
UPnP port forwarding” Enable uPnP port forwarding.
“PPPoE”
If using the PPPoE interface , fill the following
settings from ISP.
“User
name” The login name of PPPoE account.
“Password”
The password of PPPoE account.
“Confirm
password” Input password again for confirmation.
“Http port”
This can be other than the default Port 80. Once the port is
changed, the users must be notified the change for the connection to be
successful. For instance, when the Administrator changes the HTTP port of the
IT3G50-IT3G50W IT3G50/IT3G50W Network Camera whose IP address is 192.168.0.100
from 80 to 8080, the users must type in the web browser
“http://192.168.0.100:8080” instead of “http://192.168.0.100”.
“Access name” This is the access URL for making connection from client software.
Using rtsp://<ip address>/<access name> to make connection
“RTSP port” This can be other than the default Port 554
|
|
 3GPP/ISMA Function Ready.
Applications depend on local ISP provider service!
|
|
<url> http://<IT3G50/IT3G50W
Network Camera>/setup/network.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the IT3G50-IT3G50W Network Camera.
“SSID” (Service
Set Identifier), it is a name that identifies a wireless network. Access Points
and wireless clients attempting to connect to a specific WLAN (Wireless Local
Area Network) must use the same SSID. The default setting is default.
Note: The maximum length of SSID is 32 single-byte characters and SSID can’t
be any of “, <, > and space character.
“Wireless mode” Clicking on the pull-down menu to select from the following
options:
▶ “Infrastructure” Make the IT3G50W IT3G50/IT3G50W Network Camera connect to the WLAN
via an Access Point. (The default setting)
▶ “Ad-Hoc” Make
the IT3G50W IT3G50/IT3G50W Network Camera connect directly to a host equipped
with a wireless adapter in a peer-to-peer environment.
“Channel” While
in infrastructure mode, the channel is selected automatically to match the
channel setting for the selected Access Point. In Ad-Hoc mode, the channel must
be manually set to the same channel for each wireless adapter. The default
channel setting depends on the installed region.
“TX rate”
This field is for selecting the maximum transmission rate on the network. The
default setting is “auto”, that is the IT3G50W IT3G50/IT3G50W Network Camera
will try to connect to the other wireless device with highest transmitting
rate.
“Security”
Select the data encrypt method
▶ “None” – No data encryption.
▶ “WEP” – allows communication only with
other devices with identical WEP settings.
▶ “WPA-PSK” – Use WPA pre-shared key.
“Auth Mode” Choosing
one of the following modes, (Open is the default setting).
▶ “Open” – communicates the key across
the network.
▶ “Shared” – allows communication only
with other devices with identical WEP settings.
“Key length” The administrator can select the key length among 64 or 128 bits.
64bits is the default setting.
“Key format”
Hexadecimal or ASCII. “HEX” is the
default setting.
▶ “HEX” digits
consist of the numbers 0~9 and the letters A-F.
▶ “ASCII” is a code for representing English letters as numbers from 0-127
except “, <, > and space characters that are reserved.
“Network Key”
Entering a key in either hexadecimal or ASCII format. When selecting different
key length, acceptable input length is listed as following:
64 bits key length: 10 Hex digits or 5
characters.
128 bites key length: 26 Hex digits or 13
characters.
Note: When 22(“), 3C(<) or 3E(>) are input
in network key, the key format can’t be changed to ASCII format.
“Algorithm” Choosing
one of the following algorithm for WPA-PSK modes
▶ “TKIP”
▶ “AES”
“Pre-shared Key” Entering a key in ASCII format. The length of the key is 8 ~ 63
 Some invalid settings may
cause the system failing to respond. Change the configuration only if
necessary and consult with your network supervisor or experienced users for
correct settings. Once the system has lost contact, refer to Appendix A for
reset and restore procedures.
|
|
“Enable
DDNS” This option turns on the DDNS function.
“Provider” The provider list contains four hosts that provide DDNS services.
Please connect to the service provider’s website to make sure the service
charges.
“Host
Name” If the User wants to use DDNS service, this
field must be filled. Please input the hostname that is registered in the DDNS
server.
“Username/E-mail” The Username or E-mail field is necessary for logging in the DDNS
server or notify the User of the new IP address. Note: when this field is input
as “Username” the following field must be input as “Password”.
“Password/Key” Please input the password or key to get the DDNS service.
“Save” Click on this button to save current
settings for the DDNS service and UPnP function.
<url>
http://<Network Camera>/setup/ddns.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the Network Camera
The access list is to control the access permission
of clients by checking the client IP address. There are two lists for
permission control: Allow List and Deny List. Only those clients whose IP
address is in the Allow List and not
in the Deny List can connect to the
Video Server or IT3G50/IT3G50W Network Camera for receiving the audio/video
streaming.
Both Allow
List and Deny List consist of a
list of IP ranges. If you want to add a new IP address range, type the Start IP Address and End IP Address in the text boxes and
click on the Add button. If you want
to remove an existing IP address range, just select from the pull-down menu and
click on the Delete button.
Both the Allow List and Deny List can have
20 entries.
<url>
http://<IT3G50/IT3G50W Network Camera>/setup/accesslist.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the IT3G50-IT3G50W Network Camera.
“Configure
for computer viewing” To make quick setting for
computer viewing.
“Configure
for mobile viewing” To make quick setting for cell
phone viewing.
“Video
title” The text string can be displayed on video.
“Color”
Select either for color or monochrome video display.
“Frame Size”
There are four options for video sizes. “160x120”, “320x240”,
“640x480”.
“Power line frequency (for fluorescent
light)”, the fluorescent light will flash according
to the power line frequency that depends on local utility. Change the frequency
setting to eliminate uncomfortable flash image when the light source is only
fluorescent light.
There are three dependent parameters
provided for video performance adjustment.
“key
frame interval”
“Max frame rate” This limits the maximal refresh frame rate, which can be combined
with the “Video quality” to optimize bandwidth utilization and video
quality. Choose “Constant bit rate”
If the user wants to fix the bandwidth utilization regardless of the video
quality, choose “Fixed quality” and select the desired bandwidth. The
video quality may be poor due to the sending of maximal frame rate within the limited
bandwidth when images are moving rapidly. Consequently, to ensure detailed
video quality (quantization rate) regardless of the network, it will utilize
more bandwidth to send the maximal frames when images change drastically.
“Flip”
Vertically rotate the video.
“Mirror”
Horizontally rotate the video. Check options both if the IT3G50-IT3G50W
IT3G50/IT3G50W Network Camera is installed upside down.
“White balance” Adjust the value for best color temperature.
<url> http://<IT3G50/IT3G50W
Network Camera>/setup/audiovideo.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the IT3G50-IT3G50W Network Camera.
Image Settings
Click on this button to pop up another window
to tune “Brightness”,
“Contrast”, “Hue”
and “Saturation” for video compensation. Each field has eleven levels
ranged from -5 to +5. In
“Brightness” and “Contrast”
fields the value 0 indicates auto tuning. The user may press 
to fine-tune the image. When the image is O.K.,
press to set the image settings. 
Click on this to recall the original settings
without incorporating the changes.
When the SMTP server support SMTP
authentication, users need to give the valid user name and password to send email
via the server.
“Sender email address”, the email address of the sender.
There are
two external mail server can be configured, primary and secondary email server,
The IT3G50-IT3G50W IT3G50/IT3G50W Network Camera will use primary server as default , and
use secondary server when primary server is unreachable.
“Server address” The domain name or IP address of the external email server.
“User name”
This granted user name on the external email server.
“Password”
This granted password on the external email server.
“Recipient email address” The email address of the recipients for snapshots or log file.
Multiple recipients must be separated by semicolon, ‘;’.
“Built-in FTP server port number” This can be other than the default port 21. The user can change
this value from 1025 to 65535. After the changed, the external FTP client
program must change the server port of connection accordingly.
There are
two external FTP server can be configured, primary and secondary FTP server,
The IT3G50/IT3G50W Network Camera will use primary server as default , and use
secondary server when primary server is unreachable.
“Server address” The domain name or the IP address of the external FTP server. The
following user settings must be correctly configured for remote access.
“FTP server port” This can be other than the default port 21. The user can change
this value from 1025 to 65535.
“User name”
Granted user name on the external FTP server.
“Password”
Granted password on the external FTP server.
“Remote folder name” Granted folder on the external FTP server. The string must conform
to that of the external FTP server. Some FTP servers cannot accept preceding
slash symbol before the path without virtual path mapping. Refer to the
instructions for the external FTP server for details. The folder privilege must
be open for upload.
<url> http://<IT3G50/IT3G50W
Network Camera>/setup/mailftp.html
<IT3G50/IT3G50W Network Camera> is
the domain name or original IP address of the IT3G50-IT3G50W Network Camera
“Enable motion detection” Check this option to turn on motion detection.
Click on this button to add a new window. At
most three windows can exist simultaneously. Use the mouse to click, hold, and
drag the window frame to resize or the title bar to move. Clicking on the ‘x’
at the upper right-hand corner of the window to delete the window. Remember to
save in order to validate the changes.
Click on this button to save the related
window settings. A graphic bar will rise or fall depending on the image variation.
A green bar means the image variation is under monitoring level and a red bar
means the image variation is over monitoring level. When the bar goes red, the
detected window will also be outlined in red. Going back to the homepage, the
monitored window is hidden but the red frame shows when motion is detected.
"Window Name" The text will show at the top of the window.
“Sensitivity” This sets the endurable difference between two sequential images.
“Percentage”
This sets the space ratio of moving objects in the monitoring window. Higher
sensitivity and small percentage will allow easier motion detection.
The following figure shows the screen when is clicked. The monitoring window has been
outlined in red and the graphic bar goes red since the goldfish is moving.
“Enable snapshot” Enable/Disable snapshot application.
“Sun” ~ “Sat” Select the days of the week to perform the application.
Select “Always” or input the time interval.
The prefix name will be added on the file
name of the snapshot images.
There are three windows for motion
detection each can be assigned a name. Select the windows which need to be
monitored. If motion detection has not been set up, “undefined” will be
shown instead of the window title. If this happens, clicking on “Motion
detection” and a note will show to direct the User to the configuration page
for motion detection.
“Send pre-event image(s)” The number of pre-snapshots will be captured and send when a
condition is triggered.
“Send post-event image(s)” The number of post-snapshots will be captured and send when a
condition is triggered.
“Delay second(s) before detecting next
motion” Set the time delay before restarting to
check on the triggering condition when the current condition is triggered.
“Snapshot interval : second(s)” The IT3G50-IT3G50W IT3G50/IT3G50W Network Camera will send snapshots
at the specified intervals to the external server using the method selected
below. Remember: This operation is still subject to the conditions set in the
weekly schedule.
Method for
sending snapshot
“Email” This
selects the uploading method following the intervals set above. The snapshot
named “prefix-yyyymmdd-hhmmss.jpg”
will be attached in the email.
“FTP” The
snapshots will be uploaded to the external FTP server with the file name
defined in the next option. This can also be used to refresh the captured
images stored in the external web server to build creative homepages.
“FTP put snapshots with date and time
suffix” This option sets up the snapshot capture
date and time, which can be used to easily differentiate the snapshot file
names in the sequential operation. For instance, “prefix-20030102-030405.jpg” means the JPEG image was captured in
the year 2003, January the 2nd, at 3 o’clock, 4 minute, and 5
second. If this suffix is omitted, the file named “video.jpg” on the external
FTP server will be refreshed at the specified interval.
The IT3G50-IT3G50W IT3G50/IT3G50W Network
Camera support log the system messages on remote server. The protocol is
compliant to RFC 3164. If you have external Linux server with syslogd service,
use “-r” option to turn on the facility for receiving log from remote machine.
Or you can use some software on Windows which is compliant to RFC 3164.
Check “Enable
remote log” and input the “IP
address” and “port” number of
the log server to enable the remote log facility.
In the “Current
log”, it displays the current system log file. The content of the log
provides useful information about configuration and connection after system
boot- up.
Click on this link on the configuration page
to view the entire system’s parameter set. The content is the same as those in
CONFIG.INI.
Three actions can be selected :
-“reboot” click the reboot button to restart system;
-“factory
default” Click on Factory default button on the configuration
page to restore the factory default settings. Any changes made so far will be
lost and the system will be reset to the initial factory settings. The system
will restart and require the installer program to set up the network again;
-“upgrade
firmware” Select the firmware file and click
upgrade button
The following table lists the LED patterns
in general.
|
Condition
|
LED color
|
|
Loading system after power on
|
Steady blue
|
|
During booting procedure
|
Steady blue and red
|
|
Detecting and setting network
|
Steady blue and blink red till IP address
is confirmed
|
|
After network is setup (system up)
|
Blink blue every second and steady red
|
|
During the upgrade firmware process
|
Blink blue every second and fast blink
red
|
the reader should use caution to understand completely the
warnings. Ignoring the warnings may
result in serious hazards or injuries.
